Your home's exterior takes a beating every single day — sun, wind, rain, impact. When siding fails, moisture gets in fast and damage follows. Forge Siding sends licensed Siding crews across Dallas, NC to inspect, repair, and replace with zero guesswork.
Forge Siding grew out of a simple frustration: too many Dallas homeowners were paying good money for Siding work that failed inside five years. Wrong profiles, wrong fastener gauges, no housewrap — then the callbacks never came. We do it right the first time, using manufacturer-recommended installation methods and materials rated for NC's specific climate demands.
Our crews are licensed, carry full general liability and workers' comp, and every lead installer has completed manufacturer certification training. We work with fiber cement, engineered wood, vinyl, and steel systems — and we'll tell you straight which one makes the most sense for your home's structure, your local weather patterns, and your budget. No upselling, no pressure.
Most homeowners don't notice siding problems until water damage has already reached the sheathing. These are the signals worth acting on before the repair scope doubles.
Hairline cracks look cosmetic but they're water channels. Once moisture gets behind the panel and hits the housewrap — or finds no housewrap at all — sheathing rot starts within one season.
Panels that bow outward have usually absorbed moisture or were installed without adequate expansion clearance. Warped vinyl or fiber cement can't seal properly at the joints, so the problem accelerates.
Interior peeling close to an outside wall isn't a paint problem — it's a moisture infiltration problem. Your siding is the likely culprit and ignoring it turns a siding job into a drywall and mold job.
A missing panel after a wind event or impact isn't just cosmetic damage. That exposed sheathing is collecting rain until you replace it. This is one repair that can't wait for a convenient schedule.
Compromised siding reduces your wall assembly's thermal performance. If you've noticed climbing heating or cooling costs without an obvious cause, degraded siding — especially if it's letting air infiltrate — is worth investigating.
Extreme fading means UV degradation — the protective surface layer is gone. Chalking on older paint-based systems signals the same. At that stage, the panel is no longer blocking UV penetration to the substrate underneath.
Every job below starts with a free written estimate. We specify the product, the profile, the color, and the installation method upfront — so there's no ambiguity when work begins.
Fiber cement comes in lap, panel, and shingle profiles, and we've installed all three on everything from Cape Cods in historic neighborhoods to large multi-unit builds. Correct installation matters enormously with this material — improper fastening or insufficient clearances void the warranty and cause edge-swell failures. Our lead installers are trained to the spec sheet, not just to what looks right on the jobsite.
Done right, vinyl siding is durable, low-maintenance, and cost-effective. Done wrong — wrong gauge, wrong fastener pattern, no expansion clearance — it warps in the heat and pulls loose in wind. We use .044" and .046" gauge panels minimum and follow thermal expansion specs precisely for NC's temperature range. Nail hem fastening at 16" centers, 1/32" expansion gap at all trim terminations, and a fully integrated vinyl accessory system so the corners, J-channel, and window trim all work together.
Engineered wood is popular in Dallas neighborhoods where the traditional wood look matters architecturally but the maintenance demands of real cedar or pine aren't practical. We install with stainless or hot-dipped galvanized fasteners to prevent iron staining at the nail head — a detail that separates a professional installation from a quick flip job.
Not every siding problem needs a full re-side. Storm impact, vandalism, or isolated rot can often be addressed with a targeted repair that blends into the existing field. We stock common profiles and can often source discontinued patterns through our supplier network for historic or older homes where matching matters. Partial replacement work is priced honestly — if we see a repair scope that's going to creep, we say so before we start, not after.
Commercial and multi-unit projects have different demands — larger panel formats, longer exposure to foot traffic and equipment contact, stricter fire ratings in some occupancy classes, and coordinated scheduling with other trades. Forge Siding handles commercial cladding projects in Dallas, NC with full project management: dedicated site supervisor, daily progress reporting, and material delivery coordinated to minimize storage and laydown area on constrained sites.
Soffit ventilation is often compromised during re-siding work when installers don't maintain existing vent openings or fail to add ventilation where it was previously missing. We verify soffit net-free vent area against attic square footage before closing up the overhang — because your roofing contractor will find the problem later if we don't.
We built our process around the two complaints we heard from homeowners most: contractors who didn't communicate, and scopes that changed after signing. Here's exactly how a Forge Siding project runs from start to finish.
A thorough inspection before we quote means the estimate we hand you is accurate. We check the substrate, the existing housewrap or vapor barrier, window and door flashing, corner and soffit condition — all of it — so there are no hidden surprises once demo starts.
You receive a line-by-line written estimate: material cost by product and quantity, labor, removal and disposal of existing siding, and any sheathing repair identified in the assessment. We walk through material options with physical samples, not just catalog photos. You sign off on the spec before we order anything.
Your start date is locked at signing. Crew arrives on time, materials are staged and ready, and the site is protected before demo begins. We run a tight job — no leaving panels exposed overnight when rain is in the forecast.
At project completion, we walk the entire exterior with you. Every run of siding, every corner, every trim termination — you look at it before we close out. If anything isn't right, it gets fixed on the spot. Our goal is that you refer us to your neighbor the week after the project wraps.
We don't sub out work to unlicensed handymen to cut costs. Every installer on a Forge Siding project is a W-2 employee or licensed sub with verified credentials and completed manufacturer training.
Upfront pricing means you know what you're paying before a single panel comes off the wall. Change orders require your written approval. We've built our reputation in Dallas, NC on the fact that our estimates are reliable.
When we book your project, we commit to a start date. No bumping you for a bigger job, no weeks of silence after signing. We operate with enough crew capacity to honor the schedule we gave you.
Old siding demo generates a lot of debris — old panels, nails, housewrap, fasteners. We haul it out daily. Your driveway, lawn, and landscaping are clean at the end of every work day — not just at project completion.
Our workmanship warranty covers what we did and how we did it. The product carries the manufacturer's own warranty on top of ours. That means your home is protected twice — by the material the manufacturer stands behind, and by the installation Forge Siding guarantees.
Get the Details on Our Warranty — +1-844-782-0929Straight from the homeowners we've worked with across Dallas and Dallas, NC.
We were replacing deteriorated T1-11 on a house we'd bought the year before. Forge Siding walked us through why HardiePlank made more sense than vinyl for our wall orientation and explained the flashing work that needed to happen around the windows before panels went on. Project started on the date they said. Crew cleaned up every afternoon. The job came in within a couple hundred dollars of the estimate.
I manage a twelve-unit building in Dallas and we needed LP SmartSide on three facades before winter. Forge Siding coordinated with our property manager, worked around tenant schedules, delivered materials in two staged drops to keep the lot clear, and finished four days ahead of the original schedule. Commercial billing was clean and documented. They're on our preferred vendor list now.
The fascia and soffit on our older home were rotting away and we assumed it would be a nightmare project. Forge Siding quoted it alongside the siding replacement so everything was done in one mobilization. The crew found two spots where the rafter tails had started to soften — they showed me photos before touching anything and walked me through the repair options. The whole exterior looks like a different house now.
I had a specific architectural profile I wanted for the gable ends — a shingle exposure pattern — and everyone else told me it was a custom order with a six-week wait. Forge Siding had it in stock through their regional supplier and we started within two weeks of signing. The detail work at the gable peaks is clean and exact. Not every contractor has the skill to do that level of trim work.
Five-star work across the board. The crew showed up when scheduled, worked efficiently, and the lead walked me around the house at the end of each day so I could see progress and raise any questions before the next morning. The final product is outstanding — tight lap lines, perfect miters at the corners, no nail pops. My neighbor has already asked for Forge Siding's contact information.
I needed a quick turnaround on a rental property before a new tenant moved in. Forge Siding fit us in on short notice, did a clean vinyl replacement on two elevations, and the inspection cleared without a single callback item. Responsive, professional, priced fairly. That's all I ask for and they delivered all three.
Real questions, real answers — no filler.
Forge Siding sends crews to Dallas and every community within our regional service area. We keep local dispatch units strategically based so travel time doesn't eat into your project day — and so we can respond quickly when there's an emergency siding situation that can't wait.
Reach us at +1-844-782-0929 and we'll confirm service at your location. Most addresses in and around Dallas are within our standard service radius with no travel fee.
Don't let failing siding go another season. Call Forge Siding and we'll have an estimator out to your property within 24 hours.
Schedule My Assessment — +1-844-782-0929